Showing posts with label Fancy Favor box. Show all posts
Showing posts with label Fancy Favor box. Show all posts

Thursday, October 6, 2011

Owl Favor Box



Oh my gosh, I'm so excited to show you this owl box I came up with. Don't you think he is darling!















Cut a 6X 12 inch More Mustard CS with the Fancy Favor Die, assemble as directed. Cut five- 3 X1/2 strips in Not Quite Navy,(2) Cajun Craze, Almost Artichoke, and Elegant Eggplant. Start at the bottom of the favor box and attach each strip over the last one. Punch out one- 2 3/8 scallop circle in Chocolate Chip and cut in half, attach one half to each side for the wings. Punch out two Chocolate chip circles with the 1 ¼ circle punch, punch out two- 1 inch Basic Black circles, punch out two- ¾ inch circles in Very Vanilla, and punch out two-- ¼ circles in Basic Black. Punch out one- mini pendant in Tangerine Tango and cut it to a smaller size for the beak. Punch out two- scallop pendants in chocolate chip for the ears. Attach the ears to the sides and punch a hole through both and attach a black wire to carry it. Ends can be sharp so bend them inward or cover.

Saturday, August 13, 2011

Masculine Favor Box


This was one idea I had for the Fair, but decided to go with one with a flower.I used the Wilderness Stamp Set and Well Worn DSP, and the new Houndstooth embossing fiolder.
Thanks for looking,


Sunday, December 19, 2010

Stocking Box

Here is a project I used in my 12 weeks of Christams Newsletter.
I made it out of the Fancy Favor box die.

Saturday, October 2, 2010

Halloween Box


I saw some black glitter felt at Micheal's so I had to have it, and this is what I made with it.












Halloween Fancy Felt Box


Tasteful Trim Die 120893

Fancy Favor Die 115965

Table Setting Die (roses) 116819

Bitty Bat punch 119279

Crop a Dile 108362

Trim Lace 120988

Tom Bow glue 110755

1 3/8 circle punch 119860

1 inch circle punch 119868

¾ inch circle punch 119873

Basic Black CS 121045

Pumpkin Pie CS 105117

Black glitter felt

Orange felt

Various buttons

Hot Glue

Wire

Cheesecloth

DSP chipboard

1) Cut out Fancy Favor die in the felt and DSP chipboard.

2) Cut ½ inch off the decorative edge on the favor box top.

3) Tom Bow glue the chipboard to the back side of the felt box.

4) Assemble box according to directions.

5) Cut out roses from the table setting die. For smaller roses use less by cutting off the “tail”

A) Start in the middle and curl the tail around the middle until you like the size.

B) Pin the rose to hold it together while you glue it.

C) Punch out circles to match the back size of your roses.

D) Hot glue the back side of the roses, then apply the cardstock circle and push into the middle of the circle and hot glue. Remove the pin.

E) Hot glue buttons to the front center.

6) Apply orange ric rac felt around the box with Tom Bow or hot glue.

7) Hot glue the roses to the front over the ric rac.

8) Tie a small cheesecloth knot and glue next to the roses.

9) Punch holes with the Crop A Dile in each side of the box for the handle.

10) Cut 12-13 inches of wire

11) Curl the wire around a pencil then gently stretch out, you can scrunch later.

12) From the outside of the box thread one end of the wire through the hole and bend upward to the handle wire, then twist to close the wire. Do the same on the opposite side. Cut any extra wire sticking out.

13) Punch out 5 black bats.

14) Hot glue two back to back over the twisted wire at both sides. This will cover the ruff twisted wire.

15) Tie a knot from the cheesecloth and trim lace together around the handle.

16) Hot glue the last bat on the knot.